GUHRING - RT 100 VA - Сверла для обработки нержавеющих сталей и спецсплавов - 2010 EN
для размещения заказа - guhring@guhring-tools.ru
General hints: Coolant hints:
Powerful machines, no play in spindle We recommend lubrication by
bearings, alignment accurate tool soluble oil or neat oil.
holders. Max. concentricity error Under special conditions cooling
of clamped tools 0.02 mm, high just by air is possible. But instead of
coolant pressures. We recommend air cooling we would always prefer
the application of hydraulic chucks or minimal quantity lubrication, that the
shrink fit chucks. tools are especially suited for. With
MQL we recommend the conical shank
end and the Guhring MQL components.
Please contact our technical service
department for .
drill- 1 2 3 Feed column no. 7 8 9
mm 456
0.040 0.100 0.125 0.160
0.050 f (mm/rev.) 0.125 0.160 0.160
0.063 0.160 0.200 0.200
2.50 0.025 0.032 0.063 0.050 0.063 0.080 0.160 0.200 0.250
3.15 0.032 0.040 0.080 0.063 0.080 0.100 0.200 0.250 0.315
4.00 0.040 0.050 0.100 0.080 0.100 0.125 0.250 0.315 0.315
5.00 0.040 0.050 0.125 0.080 0.100 0.125 0.315 0.400 0.400
6.30 0.050 0.063 0.125 0.100 0.125 0.160 0.315 0.400 0.500
8.00 0.063 0.080 0.160 0.125 0.160 0.200 0.400 0.500 0.630
10.00 0.080 0.100 0.200 0.160 0.200 0.250 0.500 0.630 0.630
12.50 0.080 0.100 0.250 0.160 0.200 0.250 0.630 0.800 0.800
16.00 0.100 0.125 0.200 0.250 0.315
20.00 0.125 0.160 0.250 0.315 0.400
25.00 0.160 0.200 0.315 0.400 0.500
Material
Material examples, new description (further in brackets) Tens. strength Hardness Coolant
Figures in bold = material no. to DIN EN MPa (N/mm2)
Common structural steels
1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 500
Free-cutting steels 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) >500-850
1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36)
Unalloyed heat-treatable steels 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 850
1.0402 C22, 1.1178 C30E (Ck30) 850-1000
Alloyed heat-treatable steels 1.0503 C45, 1.1191 C45E (Ck45)
1.0601 C60, 1.1221 C60E (Ck60) 700
Unalloyed case hardened steels 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 700-850
Alloyed case hardened steels 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 850-1000
1.0301 (C10), 1.1121 C10E (Ck10)
Nitriding steels 1.7043 38Cr4 850-1000
1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1000-1200
Tool steels 1.8504 34CrAl6 750
1.8519 31CrMoV9, 1.8550 34CrAlNi7 850-1000
High speed steels 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1000-1200
Spring steels 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4
Stainless steels, sulphured 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 850-1000
1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) >1000-1200
austenitic 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9
martensitic 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 850
Hardened steels 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 >850-1000
– 650-1000
Special alloys Nimonic, Inconel, Monel, Hastelloy 330 HB
Cast iron 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 850
0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 850
New cast materials CGI EN-GJV250 (GGV25), EN-GJV350 (GGV35) 850
EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6
New cast materials ADI EN-GJS-800-8 (ADI800), EN-GJS-1000-5 (ADI1000) 40-48 HRC
EN-GJS-1200-2 (ADI1200), EN-GJS-1400-1 (ADI1400) >48-60 HRC
Spheroidal graphite and malleable cast 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 1200
iron 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70)
Chilled cast iron – 240 HB
Ti and Ti-alloys 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 <300 HB
3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1
Aluminium and Al-alloys 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 220 HB
Al wrought alloys 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 <300 HB
Al cast iron 10 % Si 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9
3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 800-1000
> 10 % Si 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 1200-1400
Magnesium alloys 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb
Copper, low-alloyed 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 240 HB
Brass, short-chipping 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 <300 HB
2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 350 HB
long-chipping 2.0790 CuNi18Zn19Pb 850
Bronze, short-chipping 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 >850-1200
2.0980 CuAl11Ni, 2.1247 CuBe2 400
Bronze, long-chipping 450
600
600
450
400
600
600
600
>600-850
850
>850-1000
12
guhring@guhring-tools.ru
www.guhring-tools.ru