GUHRING - Ружейные сверла - 2008 EN
для размещl1ения d1 d1 d1 d1
заказа - guhring@guhring-tools.ru d1
l3 l1 d1 d1 dd11 d l1
Additional technical parameters d1
d1
The range of drivers introduced below is available ex produce individual drivers of the highest precision to
stock. However, it only represents a small selection customer drawings. Attention! EB 100 requires drivers with
of drivers from our complete range. We naturally also positioning lugs. Further information on request.
Drivers l2 l2 Drivers
to DIN 6535
for deep drilling machines d1 Drivel1rs
to DIN 1835
1 4l2 l2 l1 9 form E 10 form HA
l3
d1 d1 d1
d1 d1 d1
l1 l1 l1 l1 l1 l1 l1 l1 l1
l3 l3
d1 l1
code no. d1 l1 l2 l3 code no. d1 l1 code no. d1 l1 d1 code no. 8 36
1.1 10 40 24 - 4.1 19,05 70 9.1 8 l136 10.1 10 40
1.2 10 40 24 45 9.2 10 40 10.2 12 45
1.3 10 40 24 55 5 l2 9.3 12 45 10.3 16 48
1.4 16 45 31,2 - 9.4 16 48 10.4 20 50
1.5 25 70 34 - l2 d1 9.5 20 50 10.5 25 56
1.6 25 70 34 78 d1 9.6 25 56 10.6 32 60
d1 9.7 32 60 10.7
2
l1 l1 l2 8 form HB
l2 l2 l l 1 Drivers l2 with code no.
8.6, 8.7, 8.8
3
l2 l2
d1 code no. d1 l1 l2 to VDI draft
d1 5.1 10 60 20 d1
5.2 16 80 28 d1
l1 l1 5.3 25 100 50 12 l1 d1
l3 l3
d1
l1
d1 d1 code no. d1 l1 l2 d1 l3 6 d1 d1 l1 l1 l1 l1
d1 2.1 16 55l100 47 - l1 l1
2.2 16 50 47 55 l1 code no. d1 l1
2.3 16 47 70
d1 code no. d1 l1 8.1 8 36
3 12.1 10 68 8.2 10 40
l1 l1 12.2 16 90 8.3 12 45
12.3 25 112 8.4 16 48
l2 l2 code no. d1 (inch) l1 8.5 20 50
6.1 1/2 38 8.6 25 56
d1d1 6.2 3/4 70 Drivers 8.7 32 60
d1 to Speed-Bit-System 8.8 40 70
7
l1 l1 l2 13 11 form HE
l3 l1 l2 l2
l3 l2 l2
34
code no. d1 l1 l3 d1 d1 l1
3.1 25 70 100
l1 l1 d1
d1 code no. d1 l1
l1 l1 d1 11.1 8 36
11.2 10 40
d1 11.3 12 45
d1 11.4 16 48
l1 l1 11.5 20 50
code no. d1 l1 d1l2 l1
7.1 16 l1112 73
7.2 20 126 82 code no. d1 l1 l2
13.1 16 40 16
l1 d1 13.2 25 50 25
d1
Examples for special point geometries for single-fluted gun drills10o
(further geometries on request)
with recessed coolant chamber with chip breaker with chip guiding step
l2 Scphaipntebirleerankuetr l1 0,4 - 0,6 +0,05 ca. 30o
15o l1
d310ox12 ox55 o 25o
d1
d1
30 o
20o
Dx0,15Dx0,13l112o 50 ox0 ox75 o15o25o 12 o
20o10 o20oDx0,05
l1 d1 30 o
12oDx0,1512o
20ol1
D D D
30o24 4
D
12oD D
Technical Section
GuhringNavigator
Driver variations to suit gun drill tubes Standard
Solution for nom.- < driver- (difference must be appr. 6 mm):
tube shank installed in driver
d1 Standard with spigot
Solution for nom.- driver- (close to pal1rallel): ~ 25 mm
tube shank installed over spigot
~ 25 mm Standard with collar
Solution for nom.- > driver-: and spigot
tube shank installed over spigot, inside- of tube shank >driver-,
tube shank fits against collar shoulder.
44 Gun drills guhring@guhring-tools.ru
www.guhring-tools.ru