HOLLFELDER - Основной каталог - 2013 EN
для размещения заказа - guhring@guhring-tools.ru
Inserts
The cutting data recommendations in the table are guide values
and depend to a high degree on the stability of the machine, xture and workpiece.
Cutting group Material group Composition / Structure Tensile Hard- Cutting speed Recommended Feed rate fz mm/z
strength ness cutting grade
RM HB vc m/min W 2006-…. W 3006-….
(MPa) HRC
100-160
1.1 C = 0.1 -0.25 annealed, long cut 420 125 110-160 G16 0.05-0.15 0.07-0.15
1.2 420 125 90-150
2.1 Unalloyed steel C = 0.1 -0.25 annealed, short chip 620 190 100-160
2.2 Cast steel 640 190 90-150
3 Machining steel C = 0.25 -0.55 annealed, long cut 850 250 80-140
4 915 270 75-125
5 C = 0.25 -0.55 annealed, short chip 1020 300 90-140
6 610 180
C = 0.25 -0.55 tempered 60-110
Low-alloy steel 275
7 C = 0.25 -0.8 annealed 60-110
300 60-100
Cast steel C = 0.25 -0.8 tempered 350
8 Machining steel 60-110
9 annealed 250
50-60
High-alloy steel tempered 930 325
10 50-90
tempered 1020 200 40-80
Cast steel tempered 1190 240 40-80
High-alloy 180 40-80
11 annealed 680 260 110-160
tool steel 180 100-150
Stainless steel hardened and tempered 1100 260 80-130
12-13 160 70-120
and cast steel ferritic/martensitic annealed 680 250 90-150
14.1 810 130 80-140
Stainless steel martensitic 610 230 -1000
14.2 880 60 -800
15 austenitisch quenched 100 -1000 G16
Grey cast iron 400 75 -800 K10/G12
16 austenitic/ferritisch (duplex) 1050 90 -600
17 Cast iron with 130 70-120 K10/PKD
18 nodular cast iron perlitic/ferritic 110 70-120
19 90 70-120 K10/G12
Malleable perlitic (martensitic) 100 -200 K10/PKD
20 -200
21 Aluminium ferritic 200 30-50 G16
22 forging alloys 230 30-50
23 perlitic 250 20-40 K10
Aluminium 350 20-40
24 ferritisch 320 20-40
casting alloys 20-40
25 perlitic 20-40
26 Copper
27 Copper alloys not heat treatable
28 (bronze, brass)
29 Non metallic aushrtbar/ausgehrtet
30 materials
31 <12% Si not heat treatable
32
Heat treatable <12% Si heat treatable/heat treated
33
alloys >12% Si not heat treatable
34
35 Machined alloys, Pb >1%
36
Titanium alloys CuZn, CuSnZn
37
Cu, lead free Copper/electrolyte copper
Duroplastic
Reinforced materials
Fe-based annealed
heat treated
Ni- or Co-based annealed
heat treated
cast
Pure titanium
Alpha-beta alloys
99
guhring@guhring-tools.ru
www.guhring-tools.ru