GUHRING - Сверла со сменными пластинами HT800 - 2010 EN
для размещения заказа - guhring@guhring-tools.ru
HT 800 WP Application Recommendations
All data are approximate values. The actually achievable cutting speeds and feed 2/3 xd1 # 4111Tol. m7
rates depend on the respective machining conditions. # 4112/4113/4114
We recommend suitable drilling trials.
~0,01
• for through holes supporting lands must remain in permanent contact. In addition, we recommend reducing
the feed rate prior to exiting. 150°
140°
• for drilling depths from 5xD we generally recommend centring or pilot drilling with holder, Guhring no.
4105, and pilot insert, Guhring no. 4111. Alternatively – depending on the material to be machined – Ratio
drills type RT 100 U or RT 100VA can be applied.
• for drilling without centring we recommend reducing the feed rate at the start of the hole.
• don‘t apply drilling tool without trial for interrupted cutting (grooves, transverse holes). For interrupted
cutting (max. 0.2 x D) it is recommended to reduce the feed rate whenever possible.
• in contrast to conventional indexable inserts, HT 800 tools are also suitable for the drilling of stacked sheets.
• on a lathe (stationary tool) it must be ensured that the tool is accurately centred.
• pre-condition for optimal machining results is a sufficient cooling lubricant supply with soluble or neat oil.
• the tool is only of limited suitability for dry machining or MQL. For MQL application we recommend the use
of the conical MQL shank end as well as Guhring MQL components. Please contact our Sales Management.
Drill- 1 2 3 Feed column no. 7 8 9 Coolant:
mm 456 air
0.014 0.016 0.019 neat oil
f (mm/rev.) 0.020 0.023 0.025 soluble oil
0.080 0.100 0.125
0.50 0.004 0.006 0.007 0.008 0.010 0.012 0.100 0.125 0.160
1.00 0.006 0.008 0.012 0.014 0.016 0.018 0.125 0.160 0.160
2.00 0.020 0.025 0.032 0.040 0.050 0.063 0.160 0.200 0.200
2.50 0.025 0.032 0.040 0.050 0.063 0.080 0.160 0.200 0.250
3.15 0.032 0.040 0.050 0.063 0.080 0.100 0.200 0.250 0.315
4.00 0.040 0.050 0.063 0.080 0.100 0.125 0.250 0.315 0.315
5.00 0.040 0.050 0.063 0.080 0.100 0.125 0.315 0.400 0.400
6.30 0.050 0.063 0.080 0.100 0.125 0.160 0.315 0.400 0.500
8.00 0.063 0.080 0.100 0.125 0.160 0.200 0.400 0.500 0.630
10.00 0.080 0.100 0.125 0.160 0.200 0.250 0.500 0.630 0.630
12.50 0.080 0.100 0.125 0.160 0.200 0.250 0.630 0.800 0.800
16.00 0.100 0.125 0.160 0.200 0.250 0.315 0.630 0.800 1.000
20.00 0.125 0.160 0.200 0.250 0.315 0.400
25.00 0.160 0.200 0.250 0.315 0.400 0.500
31.50 0.160 0.200 0.250 0.315 0.400 0.500
Material group Material examples, new description (old description in brackets) Tensile strength Hard- Cool-
Figures in bold = material no. to DIN EN MPa (N/mm2) ness ant
Common structural steels 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 500
1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500)
1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) >500-850
1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20)
Free-cutting steels 1.0402 C22, 1.1178 C30E (Ck30) 850
1.0503 C45, 1.1191 C45E (Ck45)
1.0601 C60, 1.1221 C60E (Ck60) 850-1000
1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4
Unalloyed heat-treatable steels 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 700
1.0301 (C10), 1.1121 C10E (Ck10)
1.7043 38Cr4 700-850
1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5
1.8504 34CrAl6 850-1000
1.8519 31CrMoV9, 1.8550 34CrAlNi7
Alloyed heat-treatable steels 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 850-1000
1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4
Unalloyed case hardened steels 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1000-1200
Alloyed case hardened steels 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4)
1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 750
Nitriding steels 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A)
1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 850-1000
Tool steels –
1000-1200
High speed steels
Spring steels 850-1000
Stainless steels, sulphured
>1000-1200
austenitic
martensitic 850
Hardened steels
>850-1000
650-1000
330 HB
850
850
850
40-48 HRC
>48-60 HRC
Special alloys Nimonic, Inconel, Monel, Hastelloy 1200
Cast iron 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20)
0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 240 HB
New cast materials CGI EN-GJV250 (GGV25), EN-GJV350 (GGV35)
EN-GJV400 (GGV40), EN-GJV500 (GGV50), SiMo 6 <300 HB
New cast materials ADI EN-GJS-800-8 (ADI800), EN-GJS-1000-5 (ADI1000)
EN-GJS-1200-2 (ADI1200), EN-GJS-1400-1 (ADI1400) 220 HB
Spheroidal graphite iron and 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35)
malleable cast iron 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) <300 HB
Chilled cast iron –
Ti and Ti-alloys 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 800-1000
3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1
Aluminium and Al-alloys 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 1200-1400
Al wrought alloys 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5
Al cast alloys 10 % Si 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 240 HB
3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg
> 10 % Si 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 <300 HB
Magnesium alloys 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb
Copper, low-alloyed 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 350 HB
Brass, short-chipping 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5
2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 850
long-chipping 2.0790 CuNi18Zn19Pb
Bronze, short-chipping 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 >850-1200
2.0980 CuAl11Ni, 2.1247 CuBe2
Bronze, long-chipping 400
450
600
600
450
400
600
600
600
>600-850
850
>850-1000
32 HT 800 WP
guhring@guhring-tools.ru
www.guhring-tools.ru